纺织拉挤用 TH810

纺织、拉挤用 直接无捻粗纱 Direct untwisted coarse yarn for textiles TH810

产品简介/Product introduction
TH810 是直接无捻粗纱，表面涂覆硅烷基浸润剂，适用于增强不饱和聚酯树脂、乙烯基树脂、环氧树脂，可用于拉挤、编织等应用工艺。
TH810 is a direct twist-free coarse yarn, and the surface is coated with silakyl infiltration agent. It is suitable for enhancing unsaturated polyester resin, vinyl resin and epoxy resin, and can be used for extrusion, weaving and other application processes.

产品特性/Product features

1.产品线密度稳定，单丝强度高。The product line density is stable and the monofilament strength is high.
2.工艺性能好。Good process performance.
3.耐高温、耐磨性好、毛羽低。High temperature resistance, good wear resistance, low fluff.
4.浸透速度快，与树脂相容性好。Fast penetration speed and good compatibility with resin.
5.制品机械强度高。The mechanical strength of the product is high.
产品代号/Product code
玻璃类型 Type of glass E
浸润剂类型 Type of infiltrating agent 硅烷/Silane
典型纤维直径(μm) Typical fiber diameter (μm) 13 14 16 17
典型线密度(tex) Typical line density (tex) 200 230 600 800
示例 For example EDR13-300-TH810

使用说明/Instructions for use
本产品在12个月内使用最佳，使用前应保存在原包装内。
使用时请合理控制张力并保证张力均匀性。
This product is best used within 12 months, and it should be stored in the original package before use.
When using, please control the tension reasonably and ensure the uniformity of the tension.

包装信息/Packaging information
每个纱团用 PE 缠绕膜或 PVC 热塑袋包装后放入托盘或纸箱，每个托盘可码放48个或64个纱团，每个纱团重量14-20kg，可根据用户要求定重。托盘堆高不大于2层，纸箱堆高不大于5层。可根据用户要求定制包装方式。
Each yarn ball is packed in a PE wrapping film or PVC thermoplastic bag and put into a pallet or carton. Each pallet can put 48 or 64 yarn balls. Each yarn ball weighs 14-20kg, which can be weighed according to user requirements. The height of the pallet should not exceed 2 layers, and the height of the carton should not exceed 5 layers. The packaging method can be customized according to user requirements.

贮存/Save up
TH810 建议贮存在干燥、通风和防水的地方，环境温度控制在 5℃-35℃，相对湿度 35%-75%，产品不使用时，请勿打开包装物或扎紧包装口，以免受潮。为确保安全，避免损坏产品，托盘的堆码高度不应超过三层。当堆放两层或三层高时，要求正确地、平稳地移动上面的托盘。
TH810 recommends storage in a dry, ventilated and waterproof place. The ambient temperature is controlled at 5℃-35℃, and the relative humidity is 35%-75%. When the product is not in use, please do not open the package or tighten the packaging mouth to avoid moisture. In order to ensure safety and avoid damaging the product, the stacking height of the pallet should not exceed three layers. When stacking two or three layers high, it is required to move the tray on it correctly and smoothly